- New
- To order
600-litre tank with a thermal oil jacket to hold, settle and sterilise beeswax. Two 6 kW heaters, digital control and two outlets: one for the sediment and one for the clean wax. AISI 304 stainless steel with stone wool insulation. Three-phase. Thermal oil (100 to 110 litres) is not included. Supplied to order.
|
600 L CAPACITY |
2 × 6 kW HEATERS IN THERMAL OIL |
|
2 outlets SEDIMENT AND CLEAN WAX |
Ø 850 mm INNER DIAMETER |
600-litre tank with a thermal oil jacket to hold, settle and sterilise beeswax at foundation-maker or co-operative scale.
It is made of AISI 304 stainless steel, triple-walled, with stone wool insulation. It is not a steam wax melter: here the wax is heated dry, through the oil. Before ordering, it helps to know what the unit controls and what you have to control yourself.
01 · WHAT IT'S FOR
It works as the holding tank of a foundation machine: it keeps the wax liquid at a steady temperature and delivers it clean. It works as a settling tank: left to rest, sediment and water sink to the bottom and the clear wax stays on top. And because it heats with oil rather than water, it can go above 100 °C, which is what sterilisation needs. Filled to 90 %, it takes around 440 kg of wax. If what you want is to get the wax out of old frames and combs, this is not the machine: a steam wax melter does that, and this tank then takes the wax already melted or in blocks.
02 · HOW IT HEATS
The jacket covers the bottom, with 100 mm of oil, and the walls, with 30 mm. It has two 6 kW heaters on the side, near the bottom, and can run on one only if your supply is tight. The thermal oil is not included: it takes 100 to 110 litres, and good-quality oil is worth it. The jacket has a level indicator, a drain valve and a vent on top so the oil can expand.
Check the level from time to time: without oil, the heaters burn out, and replacing them means draining the jacket.
03 · THE CONTROL
The digital controller reads the oil temperature. The wax always lags behind, all the more in a tank with no stirrer. The unit has no independent safety thermostat: at 12 kW it is not something to leave heating unattended.
To sterilise against American foulbrood spores, our protocol for thermal oil tanks is to bring the wax to about 125 °C and hold it for at least 60 minutes, measured with a probe in the wax, which you will have to fit yourself. Then lower it to about 80 °C to settle. Two warnings: sterilising does not remove acaricide residues, and wax from colonies killed by American foulbrood is not recycled into foundation.
04 · OUTLETS AND INSTALLATION
The bottom is flat, with a drainage channel that empties it completely. The bottom valve sits 420 mm from the floor and takes out water and sediment. The second one is about 9 cm higher, at 510 mm, and gives clean wax without stirring up what has settled. Both are stainless steel and are not heated: if the wax sets in the valve, it has to be warmed before opening.
It needs a 380 V three-phase supply. It measures 1,000 mm in outer diameter and the loading rim is at 1,470 mm: think about how you will lift the wax up. The lid is hinged, stainless steel and not insulated.
05 · BEFORE YOU BUY
It is supplied to order and we confirm the lead time when you order. If you are unsure between this tank and a smaller one, tell us how many kilos of wax you handle per batch and which foundation machine you work with.
| ✓ SUITS | Foundation makers, co-operatives and operations that work wax in batches of several hundred kilos. |
| ✕ DOES NOT SUIT | Melting frames or combs, or unattended work: it has no safety thermostat. |
| ⚠ NOT INCLUDED | Thermal oil (100 to 110 litres), wax probe, electrical installation or assembly. |
| Reference | 9056 |
|---|---|
| Capacity | 600 L |
| Material | AISI 304 stainless steel · 3 mm inner sheet |
| Construction | Triple-walled, with stone wool insulation |
| Heating | Thermal oil jacket: 100 mm under the bottom and 30 mm around the walls |
| Thermal oil | 100 to 110 L · not included |
| Power | 2 heaters of 6 kW · can run on one only |
| Power supply | Three-phase, 380 V |
| Control | Digital · reads the oil temperature |
| Outlets | 2 stainless steel valves, 420 and 510 mm from the floor |
| Diameter | Inner 850 mm · outer 1,000 mm |
| Loading rim height | 1,470 mm |
| Lid | Hinged, stainless steel, not insulated |
| Manufacturer's warranty | 24 months |
Write your question
600-litre tank with a thermal oil jacket to hold, settle and sterilise beeswax. Two 6 kW heaters, digital control and two outlets: one for the sediment and one for the clean wax. AISI 304 stainless steel with stone wool insulation. Three-phase. Thermal oil (100 to 110 litres) is not included. Supplied to order.
check_circle
check_circle