Candle mould - Holy Family

36 .40 €

FS15

Candle mould - Holy Family

Share in WhatsApp

36 .40 €

Tax included

Stock

One-piece, uncut FS15 silicone mould for a Holy Family relief about 11 × 10 cm, using approximately 150 g of wax. The manufacturer specifies no wick: if the piece is to be burned, select it for the wax and validate stability and burning behaviour before making further units.

36 .40 €

Tax included

Stock

Quantity

Select options Options

Express Shipping

Return Guarantee

Safe payment

Details of Candle mould - Holy Family

FS15

MODEL

11 × 10 CM

CAST

≈150 G

WAX

UNCUT

ONE PIECE

FS15 silicone mould for making a Holy Family relief approximately 11 cm high by 10 cm wide, with an indicative wax requirement of 150 g.

This is a one-piece, uncut relief mould: it does not make the smaller three-dimensional Holy Family figurine also listed by LTA.

01 · IDENTIFY THE FORMAT

FS15 relief with a flat back

The mould itself is 13 cm high; the finished cast is about 11 × 10 cm. The manufacturer labels the second cast measurement as diameter, although on this scene it represents the maximum width. The 150 g figure is an estimate for wax and can change with density, fill level and shrinkage. The product supplied is the mould; the yellow item in the photographs demonstrates the result and is not part of the contents.

02 · PREPARE AND POUR

Wick and temperature depend on the project

Work with the mould dry, clean, level and properly supported. For a candle intended to burn, position a centred wick before pouring, but do not rely on any inherited wick size: the manufacturer specifies no wick for FS15. Select it for the wax and final geometry, then validate it with a burn test. Melt without direct flame and follow the material supplier's pouring guidance; the official page mentions both 50 and 60 °C in different sections, so neither is a universal setting. Pour slowly to reach the relief details and do not move the mould while the cast sets.

03 · COOL AND RELEASE

Flex the silicone; do not cut it

Wait until the whole cast is cold and firm. Peel the silicone away gradually from the edges and release the deeper details first; never pull on the wick or insert knives that can score or tear the mould. The manufacturer allows silicone spray inside to aid release: use it only when it is compatible with the chosen casting material and the intended end use. Remove residues after they have cooled and store the mould without folds or weight on top.

04 · BEFORE YOU BUY

Match the material and intended end use

The manufacturer lists beeswax, soy and palm wax, paraffin, ceramic plaster, creative concrete, epoxy resin and soap base. Each requires its own safety data, ventilation, protection, temperature or mixing ratio and cure time. Keep separate moulds where residues or cross-contamination matter. Before selling or gifting a candle that will be lit, test one unit for stability, flame height, melt pool and behaviour through the full burn; FS15 has no wick specification.

THIS IS FS15	One-piece Holy Family relief, approximately 11 × 10 cm cast and about 150 g of wax.
CHECK	Wick, temperature, release and safety against the exact wax or casting material; no value is universal.
DO NOT CONFUSE	With FS564, the small Holy Family figurine, or with a split three-dimensional figure mould.

CONFIRMED DATA AND LIMITS

Product	FS15 silicone mould
Reference	FS15
EAN	5903661502607
Stated material	Silicone · grade not published
Format	Relief mould · one piece · uncut
Mould height	13 cm
Cast	11 cm high × 10 cm maximum width
Indicative wax	150 g · may vary
Wick	Not specified by the manufacturer for FS15
Stated casting media	Waxes · paraffin · ceramic plaster · creative concrete · epoxy · soap base
Not documented	Grade/hardness · maximum temperature · service life · cleaning · tolerances · food contact